13.3inch HDMI LCD (H)

From Waveshare Wiki
Jump to: navigation, search
13.3inch HDMI LCD (H)
13.3HP-1.jpg

IPS, 1920x1080, 13.3 inch Capacitive Touch Screen LCD, Supports Multi mini-PCs, Multi Systems
{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

Primary Attribute
Category: OLEDs / LCDs, LCD, Raspberry Pi LCD
{{{userDefinedInfo}}}: {{{userdefinedvalue}}}
Brand: Waveshare
Website
International: Website
Chinese: 官网
Onboard Interfaces
USB HDMI
Related Products

Introduction

13.3inch IPS screen, 1920x1080 high rsolution.Toughened class cover. Supports Multi mini-PCs, multi systems.

more

Features

  • 13.3inch IPS screen,1920x1080 high resolution
  • Toughened glass capacitive touch panel, 6H hardness
  • When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free
  • When work as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free
  • Multi-languages OSD menu, for power management, brightness/contrast adjustment, etc.
  • 3.5mm audio jack supports HDMI audio output

Working with PC

This product supports Windows 10/8.1/8/7 OS.:

1. Connect 12/1A power adapter to the DC interface of LCD, after connecting the back light will light.

2. Connect the TOUCH interface of LCD to the USB interface of PC . Waiting for a moment, The touch will be recognized by Windows automatically

3. If you use HDMI, you need to connect the HDMI interface of LCD to the HDMI port of PC. About 5s later, you can see that the LCD display properly. If you need the audio, you can insert a 3.5mm earphones to HP ports.

4. Use VGA,you need to connect the VGA interface of LCD to PC's VGA ports by Mini HDMI to VGA Cable

Note:

1) If multi screen are connected to one PC at the same time, you can only control the cursor by this LCD, so please set the LCD as main screen.

2) Some of PC cannot support HDMI screen Hot Plug . In this case, restart the PC can solve.

3) HP audio output only works while using HDMI communication

4) Mini HDMI to VGA Cable is necessary and need to be purchased separately if you use VGA communication.

Calibration touch on Win 10 PC

Take the windows10 system as an example:

  • 1. Enter the Windows settings of the system, type in the search bar and click "Calibrate the screen for pen or touch input" (as shown in the picture below)

Win10 touch011.png

  • 2. Click "Setup" in the pop-up "Tablet PC Settings" interface:

Win10 touch02.png


  • 3. The following text prompt will appear on the screen. Please tap the touch screen with your finger, and the computer will recognize it as a touch screen.

【Note】If the touch screen is blank, press the "Enter" key, and the text prompt will switch to the touch screen. (The screen which displays the text prompt will be used as a touch screen!)

Win10 touch03.png

Working with Raspberry Pi

Supports Raspbian/Ubuntu mate/Windows 10 iot Core

When working with Raspberry Pi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work. For more detail information, please read the following section.

Download the Raspbian image from Raspberry Pi web site. Write the image to a TF card and append the following lines to the config.txt file which is located in the root of your TF card:

max_usb_current=1
hdmi_group=2
hdmi_mode=82
hdmi_cvt 1920 1080 60 6 0 0 0

You must make sure that there are no spaces on either side of the equal sign.

Connect the Touch interface of LCD to the USB port of Raspberry Pi

Connect the HDMI interface of LCD to HDMI port of Raspberry Pi

Save and connect the TF card to your Pi then power up.

Rotation(Working with Raspberry Pi)

Display Rotating

Add this statement in the config.txt file (the config file is located in the root directory of the TF card, which is named /boot):

display_rotate=1 #1:90;2: 180; 3: 270

Note: For Raspberry Pi 4, you need to comment out dtoverlay=vc4-fkms-V3D.

#dtoverlay=vc4-fkms-V3D.

And then restart the Raspberry Pi after saving.

sudo reboot

Touch Rotating

After the display is rotated, the position of touch is incorrect because the touch doesn’t change with the display angle. So the touch also needs to be modified.

1.Install libinput.

sudo apt-get install xserver-xorg-input-libinput

If the system you installed is Ubuntu or Jetson Nano. The installation code is:

sudo apt install xserver-xorg-input-synaptics

2.Create the xorg.conf.d directory under /etc/X11/ (if the directory already exists, proceed directly to step 3).

sudo mkdir /etc/X11/xorg.conf.d

3.Copy the 40-libinput-conf file to the directory you created just now.

sudo cp /usr/share/X11/xorg.conf.d/40-libinput.conf /etc/X11/xorg.conf.d/

4.Edit this file.

sudo nano /etc/X11/xorg.conf.d/40-libinput.conf

Find the part of the touchscreen, add the following statement inside, and then save the file.

Option "CalibrationMatrix" "0 1 0 -1 0 1 0 0 1"

Similar to the picture below:

Touch roate.jpg
5. save and reboot your Pi

sudo reboot

After completing these steps. The LCD could rotate 90 degrees both display and touch function.

Note:

90 degree: Option "CalibrationMatrix" "0 1 0 -1 0 1 0 0 1"

180 degree: Option "CalibrationMatrix" "-1 0 1 0 -1 1 0 0 1"

270 degree: Option "CalibrationMatrix" "0 -1 1 1 0 0 0 0 1"

Demo video about rotating

External guides

FAQ

Question:
What is the operating current of 13.3inch HDMI LCD H
Answer:
This LCD get power from two interfaces. One is the POWER port, you should connect an 12V/1A power adapter to this interface, the operating current of this interface is about 12V/0.6A. And the other one is the TOUCH interface. You need to connect this interface to the USB interface of master, its operating current is about 5V/80mA


Support

If you require technical support, please go to the Support page and post a tickets.