≥1:
US $3.39840
Buy(0)
Inquiry(0)
Dear customers, due to the implementation of the GDPR policy in Europe, UTSOURCE has also made adjustment accordingly to meet the policy requirements. Please read the new privacy policy carefully and this window will no longer pop up after you accept it.
Delivery Address
+ Add Address
The new shipping address
* Please fill in the cell phone number correctly to make sure that you can receive the tracking info in time.
Country CodeSearch results filter:
Home > Elec-component > IC Chips > PMIC - Motor Drivers, Controllers
Description: The LA6565-TE-L-E is a low-noise, high-efficiency, low-dropout linear regulator IC from Sanyo Semiconductor. Features: Low output noise: 40μVrms (typical) High efficiency: 95% (typica
Stock:10000
Minimum:2
Favorite
Description: The DRV8301DCA is a three-phase gate driver IC for brushless DC (BLDC) motors. It is designed to drive three N-channel power MOSFETs in a three-phase bridge configuration. Features: - Hi
Stock:5000
Minimum:1
Favorite
HTSSOP-28
Texas Instruments
13+
The DRV8841 provides an integrated dual H-bridge motor driver solution for printers, scanners, and other automated equipment applications. The device can be used to drive one or two brushed DC motors, a bipolar stepper motor, or other loads. A simple PWM interface allows easy interfacing to controller circuits. The output driver block consists of N-channel power MOSFETs configured as H-bridges. The DRV8841 an supply up to 2.5-A peak or 1.75-A RMS output current (with proper heat sinking at 24 V and TA = 25°C) per H-bridge. A low-power sleep mode is provided which shuts down internal circuitry to achieve very low quiescent current draw. This sleep mode can be set using a dedicated nSLEEP pin. Internal protection features are provided for overtemperature, overcurrent, and undervoltage. Fault conditions are indicated by a nFAULT pin.
The DRV8841PWPR is a dual full-bridge motor driver from Texas Instruments. It is designed to drive two brushed DC motors with a voltage range of 4.5 V to 36 V. It features a low RDS(on) of 0.3 Ω, a lo
Stock:10000
Minimum:2
Favorite
DIP28
National Semiconductor
The LM629N-8/NOPB is a dedicated Motion-control Processor designed for use with a variety of DC and brushless DC servo motors and other servomechanisms which provide a quadrature incremental position feedback signal. The parts perform the intensive, real-time computational tasks required for high performance digital motion control. The host control software interface is facilitated by a high-level command set. It has an 8-bit output which can drive either an 8-bit or a 12-bit DAC. The components required to build a servo system are reduced to the DC motor/actuator, an incremental encoder, a DAC and a power amplifier. An LM629-based system is similar, except that it provides an 8-bit PWM output for directly driving H-switches. It incorporates an SDA core processor and cells designed by SDA.
Description: The LM629N-8/NOPB is a high performance, monolithic, servo loop motor controller designed to provide closed loop control of brushless DC motors. Features: - High performance, monolithic,
Stock:10000
Minimum:1
Favorite
Stock:10000
Minimum:1
Favorite
Description: The MPC17533EVEL is a 16-pin TSOP (Thin Small Outline Package) from Freescale Semiconductor. It is a low-power, low-voltage, low-cost, high-performance 8-bit microcontroller. Features:
Stock:10000
Minimum:1
Favorite
NCV7517BFTR2G is a low-dropout (LDO) voltage regulator with an output voltage of 1.8V and a maximum output current of 1.5A. It is designed to provide a regulated output voltage in applications where t
Stock:5000
Minimum:1
Favorite
DIP-40
Avago
2010
General Purpose Control ICs Position and Velocity Control Low Power CMOS
Stock:2000
Minimum:1
Favorite
Stock:10000
Minimum:2
Favorite
Description: STMicroelectronics L9958 is a high-side power switch IC with integrated protection features. Features: High-side power switch Over-current protection Over-temperature protection Short
Stock:5000
Minimum:1
Favorite
Stock:10000
Minimum:3
Favorite
Description: The VNH2SP30-E is a full bridge motor driver IC from STMicroelectronics. It is designed to drive brushed DC motors in a wide range of applications. Features: High current capability:
Stock:2000
Minimum:1
Favorite
Stock:5000
Minimum:1
Favorite
Stock:10000
Minimum:2
Favorite
HTSSOP28
Texas Instruments
1323+
STEPPER MOTOR CONTROLLER IC 1 DRV882 5PWPR Datasheets Search Partnumber : Start with "DRV882 5PWPR " - Total : 31 ( 1/2 Page) NO Part no Electronics Description View Electronic Manufacturer 31 DRV8821 DUAL STEPPER MOTOR CONTROLLER/DRIVER
DRV8825PWPR is a high-performance microstepping motor driver with a wide range of features and applications. It is designed to drive bipolar stepper motors in full, half, quarter, eighth, and sixteent
Stock:10000
Minimum:1
Favorite
Description: The A4973SLBTR-T is a fully integrated microstepping motor driver with built-in translator for easy operation. It is designed to operate bipolar stepper motors in full, half, quarter, and
Stock:10000
Minimum:2
Favorite
Description: The L6472PD is a PowerSO-36 package motor driver IC from STMicroelectronics. It is a dual full-bridge driver with integrated power MOSFETs and a microstepping indexer. Features: Int
Stock:2000
Minimum:1
Favorite
Description: The U2008B-MY is a high-speed, low-power, 8-pin DIP (dual in-line package) transistor–transistor logic (TTL) device manufactured by TFK. Features: * Low power consumption * High-speed op
Stock:5000
Minimum:1
Favorite
Description: L6225PD is a high-side power switch designed for automotive applications. It is a monolithic integrated circuit in a HSOP20 package. Features: - High-side power switch - Low RDS(on) - Ov
Stock:2000
Minimum:1
Favorite
Description: Dual High-Speed MOSFET Driver Features: High-Speed MOSFET Drivers Low-Power CMOS Logic High-Current Outputs Low-Voltage Operation Low-Voltage Lockout TTL/CMOS Compatibl
Stock:10000
Minimum:1
Favorite
Stop production experts, we can provide a large number of electronic components that have been stopped production and are difficult to find, to facilitate the maintenance company